|
|
|
|
|
|
|
|
|
|
|
Designed for drainage in areas where waterproofing membrane is not required. Plastic Snap-In Drain can be solvent welded or inserted into Sch. 40 DWV pipe. One piece design does not allow for removal of the cover.
|
4-1/4" x 4-1/4" Stainless steel square tile ring. For use with the 151 Series Oatey drains.
|
Designed for drainage in areas where waterproofing membrane is not required. Plastic Snap-In Drain can be solvent welded or inserted into Sch. 40 DWV pipe. One piece design does not allow for removal of the cover.
|
|
|
|
|
|
|
|
|
|
|
|
|
Designed for drainage in areas where waterproofing membrane is not required. Plastic Snap-In Drain can be solvent welded or inserted into Sch. 40 DWV pipe. One piece design does not allow for removal of the cover.
|
Adds a decorative flair to a basic tub spout. Covers gaps and holes. 3-5/8" OD, 2-1/4" ID.
|
Strainer dome cover with screw.
|
|
|
|
|
|
|
|
|
|
|
|
|
Plumb Pak Tub Overflow Washer, Flat, Sponge
|
Adds a decorative flair to a basic tub spout. Covers gaps and holes. 3-5/8" OD, 2-1/4" ID.
|
Chrome plated face plate screws.
|
|
|
|
|
|
|
|
|
|
|
|
|
Installs to standard 1/2" shower arms. 2.0 gpm flow rate.
|
Adjustable Spray. Installs to standard 1/2" shower arm. 2.5 GPM flow rate.
|
Standard 1/2", Plastic. Overall length 7".
|
|
|
|
|
|
|
|
|
|
|
|
|
3-5/16" O.D. 6.88" h x 4-3/4" w.
|
2" PVC offset shower drain with receptor base. Solvent welds over 2" schedule 40 DWV pipe. Universal 4-1/4" Snap-Tite strainer. Drain body provides 1-1/2" offset to work around joists and imperfect slab penetrations. Drain body is sealed to shower base with rubber gasket and fiber slip washer.
|
Zinc body; chrome plated finish with reducer bushing. For 3/4'' or 1/2'' pipe.
|
|
|
|
|
|
|
|
|
|
|
|
|
For use on steel, fiberglass and other types of plastic shower bases. Solvent welds to 2" DWV or Schedule 40, ABS or PVC pipe. 4-1/2" flange diameter, with stainless steel grid.
|
Shower arm diverter, plated plastic, connects personal shower and shower head. 1/2" F.I.P. x 1/2" M.I.P. x 1/2" M.I.P
|
Shower flow adjuster. 1/2" IPS.
|
|
|
|
|
|
|
|
|
|
|
|
|
Zinc body. Screws included.
|
Standard 1/2", Plastic. Overall length 7".
|
Plumb Pak Tub Face Plate, 1-Hole, Trip lever Style, Suitable For Use With: Bath Drain, Chrome Plated
|
|
|
|
|
|
|
|
|
|
|
|
|
Plated plastic. Flow control and shut off.
|
For trip lever 6" eye wire. 10-32 brass eye bolt. Brass clevis plunger.
|
Designed for use with preformed shower stall bases. The drain seals to the base with fiber and rubber washers. 2" Schedule 40 DWV pipe solvent welds to the drain base. Drain top accommodates 4-1/4" universal Snap-Tite Strainers available in a variety of designer finishes. Drain body is sealed to shower base with rubber gasket and fiber slip washer.
|
|
|
|
|
|
|
|
|
|
|
|
|
Designed for use with preformed shower stall bases. The drain seals to the base with fiber and rubber washers. 2" Schedule 40 DWV pipe solvent welds to the drain base. Drain top accommodates 4-1/4" universal Snap-Tite Strainers available in a variety of designer finishes. Drain body is sealed to shower base with rubber gasket and fiber slip washer.
|
4-1/4". For 101 PNC and 140 NC No-Calk snap-in shower drains, and 101 PS solvent weld and 2-part shower drains.Carded.
|
Designed for use with preformed shower stall bases. The drain body is sealed to the shower base with a fiber and rubber washer. 2" Schedule 40 DWV pipe is secured with a mechanically compressed gasket that does not require caulking. Drain top accommodates 4-1/4" Universal Snap-Tite strainers available in a variety of designer finishes. Compression gasket tightens around 2" Sch. 40 DWV pipe with caulking nut & wrench. Can be used with 1-1/2" Sch. 40 DWV pipe and 1-1/2" or 2" Copper DWV pipe when caulking gasket is replaced.
|
|
|
|
|
|
|
|
|
|
|
|
|
Threaded shaft.
|
Plumb Pak Tub Face Plate, 2-Hole, Blank Overflow, Suitable For Use With: Bath Drain, Chrome Plated
|
Fully adjustable spray, 1.5 gpm average flow.
|
|